伞帽用高铬铸铁在热强碱腐蚀环境下的磨损分析

针对氧化铝行业中常用的Cr28和Cr20高铬铸铁伞帽在相同工况条件下的磨损机理进行分析,并对比研究了实际生产中两种失效材料的成分、组织及性能。结果表明,伞帽部件在高温强碱腐蚀条件下受到外界冲刷时,磨损量由微切削磨损与变形磨损这两种机制共同决定。含铬量较高的Cr28高铬铸铁,其冲刷和抗腐蚀磨损性能均优于Cr20高铬铸铁。伞帽服役寿命主要受浆料和表层的铸铁材料两大因素影响。两种试验材料经淬火+回火处理后,基体组织中主要为回火马氏体+M₇C₃型碳化物+少量残留奥氏体,其中含铬量较高的Cr28高铬铸铁中共晶碳化物含量更高,且分布更加弥散,其平均硬度值为64.0 HRC,高于Cr20高铬铸铁的60.2 HRC。最终确定Cr28高铬铸铁作为伞帽材质更能满足氧化铝生产及设备检修周期的需要。     

长管拖车缠绕气瓶纤维层冲击损伤的数字射线检测

采用缠绕气瓶替代钢制无缝气瓶是长管拖车轻量化的重要手段之一,但对于缠绕气瓶缠绕层因冲击造成的内部损伤,目前仍缺少成熟有效的检测手段。采用数字射线检测方法,针对玻璃纤维缠绕层冲击损伤造成的分层和危害较大的纤维断裂进行了试验研究。试验表明,采用数字射线检测能够有效检测最小深度为0.5 mm模拟纤维环向断裂刻槽和0.25 mm的模拟纤维轴向断裂刻槽;此外,还通过试验验证增加补偿块的方式,能极大地改善缠绕层分层部位的一次切向透照成像质量,进而提高检测效率。     

Evaluation on Dorsey Method in Surface Tension Measurement of Solder Liquids Containing Surfactants

With the purpose of developing a feasible approach for measuring the surface tension of solders containing surfactants, the surface tension of Sn–3Ag–0.5Cu–xP solder alloys, with various drop sizes as well as different phosphorus (P) content, was evaluated using the Dorsey method based on the sessile drop test. The results show that the accuracy of the surface tension calculations depends on both of sessile drop size and the liquid metal composition. With a proper drop size, in the range of 4.5 mm to 5.3 mm in equivalent spherical diameters, the deviation of the surface tension calculation can be limited to 1.43 mN·m^?1 and 6.30 mN·m^?1 for SnAgCu and SnAgCu–P, respectively. The surface tension of SnAgCu–xP solder alloys decreases quickly to a minimum value when the P content reaches 0.5 wt% and subsequently increases slowly with the P content further increasing. The formation of a P-enriched surface layer and Sn₄P₃ intermetallic phases is regarded to be responsible for the decreasing and subsequent increasing of surface tension, respectively.     

基于CorelDraw的地理国情普查数据成果图集图外装饰设计

在2016年国务院全国第一次地理国情普查领导小组办公室颁布的《地理国情普查成果图技术规定》的基础上,利用Corel Draw软件,对福州市第一次地理国情普查数据成果图集图外装饰部分作专门设计,使图集不仅能够达到国家要求技术规定,同时体现福州文化特色。     

A Generalized Surface Chalcogenation Strategy for Boosting the Electrochemical N2 Fixation of Metal Nanocrystals

Electrocatalytic nitrogen reduction reaction (NRR) is a promising process relative to energy-intensive Haber–Bosch process. While conventional electrocatalysts underperform with sluggish paths, achieving dissociation of N₂ brings the key challenge for enhancing NRR. This study proposes an effective surface chalcogenation strategy to improve the NRR performance of pristine metal nanocrystals (NCs). Surprisingly, the NH₃ yield and Faraday efficiency (FE) (175.6 ± 23.6 mg h^–1 g^–1_Rh and 13.3 ± 0.4%) of Rh-Se NCs is significantly enhanced by 16 and 15 times, respectively. Detailed investigations show that the superior activity and high FE are attributed to the effect of surface chalcogenation, which not only can decrease the apparent activation energy, but also inhibit the occurrence of the hydrogen evolution reaction (HER) process. Theoretical calculations reveal that the strong interface strain effect within core@shell system induces a critical redox inversion, resulting in a rather low valence state of Rh and Se surface sites. Such strong correlation indicates an efficient electron-transfer minimizing NRR barrier. Significantly, the surface chalcogenation strategy is general, which can extend to create other NRR metal electrocatalysts with enhanced performance. This strategy open a new avenue for future NH₃ production for breakthrough in the bottleneck of NRR.     

寒冷地区某既有办公建筑围护结构优化改造研究

既有公共建筑能耗中,围护结构节能潜力巨大。以兰州某既有办公建筑为例,采用DeST-C软件模拟围护结构不同材料厚度、窗型,得出系列负荷,通过对数据分析、比较,得出如下结论:外墙外保温适宜材料为50mm的挤塑板,最大热负荷节能率为45.66%;屋面适宜保温材料为65mm的挤塑板,最大热负荷节能率为4.25%;外窗各个朝向全部更换玻璃,推荐选用内张膜中空玻璃(双膜),最大热负荷节能率为7.36%;单独更换南向外窗材料,推荐选用真空镀膜复合中空玻璃,最大热负荷节能率为1.78%。     

KF-NaF-AlF3 System: Liquidus Temperature and Phase Transition

JOM - The development of low-temperature aluminum electrolysis makes it possible to reduce energy consumption and greenhouse gas emissions. The KF-NaF-AlF3-based electrolyte is a promising...     

Thermal management and catalytic combustion stability characteristics of premixed methane/air in heat recirculation meso‐combustors

In order to illuminate heat recirculation effect on catalytic combustion stability and further improve energy conversion efficiency in meso‐combustor, the catalytic combustion characteristics of the combustor with/without preheating channels are numerically studied at steady conditions. It is found that methane conversion rate and combustion efficiency increases by 2% to 3% and approximately 9% in the heat recirculation meso‐combustor, indicating that heat recirculation effect facilitates more complete combustion of methane and medium components. Preheating channels show positive effects on improving combustion stability in the heat recirculation meso‐combustor. On one hand, preheating channels facilitate heat recirculation effect, and heat recirculation rate exceeds 10% for all cases and reaches 31.8% with an inlet velocity of 0.5 m/s, leading to significant increment of methane‐specific enthalpy at the preheating channel outlet. On the other hand, Rh(s)/O(s) ratios of catalytic surface and catalytic surface temperature in main reaction zone are enlarged by the preheating channels, facilitating methane adsorption at catalytic surface. Specially, most of fuels are consumed in a shorter distance with higher methane conversion speed, which brings benefits to promote combustion efficiency and may be helpful to inhibit the combustion instability in heat recirculation meso‐combustors.